My background is in Finance, so there you go. I have zero background in IT or networking. I want to create a portable Plex Media Server on an External SSD running ubuntu.įirstly – I must emphasise that my ubuntu / linux knowledge is very minimal. An on-going ubuntu experiment and learning experience for me. This will be a progressive setup, I would rather get hardware that will last into the future and add components over time for each feature that I add.This is a strange project. I was told that the Dell T30 supports up to 10TB HDD per slot and there are 4 slots available.Īre there any other servers I should consider ? The Plex website states that a single 1080p/10Mbps stream will require a passmark of 2000, the Dell T30 has a passmark of 7762 so this must be more than enough ? This is why I have been looking at servers rather than a NAS. I am looking for hardware that will be flexible, upgradeable and scalable. To get started I want to get a server and install a HDD to store my media so that I can use the server as a media server. Thanks for the replies - I already have backups of my data on a collection of portable USB HDDs as well as another backup on a WD Desktop 5TB HDD which is kept offsite.Įventually I want to use the server as a backup but this will have to wait until I can afford to purchase all the HDDs to put in the server. It's probably better to wait a little and get something that fits your needs today and is able to expand later on to suit your future needs, otherwise you will end up with two servers and a higher cost of ownership at the end of it all. Plus remember that when you want to expand to a much larger pool (personally for media alone I would suggest at least a total of 10 TB usable) you need places to put those drives or you will need to buy very large drives. I would say at least 16GB and more is ALWAYS better. All of my devices do just fine with MP4 so I rarely transcode on the fly unless I am away from home and have a poor internet connection.ĨGB of ram however is pretty small when you want to use Plex. This should also work with the nvidia shield but you will need to search around and figure out what it likes. You just handle that when you encode the media. You can apply multiple audio streams to one video container to get what ever you want out of it, like one device only needs stereo but another you want DTS. Also you should try to figure a format that will support MULTIPLE devices without transcoding. That can be figured on the plex website Īlso remember that the more you want to do with it the more cpu and ram you want available and the expand-ability of the server. You will however need to figure how many streams you want to be able to transcode at one time and figure out what you need to be able to do that for the number of streams you desire. You should always have backups but if one drive goes down it's up in smoke with no chance of recovery.Īny of the servers you mentioned should work ok but that is without checking the ram available or possible disk controllers included. Samsung Smart TV running Plex client (UE32K5500)Ĭan you do it with one drive, sure but that kinda defeats the purpose so you will want to have REALLY good backups.Samsung Smart TV running Plex client (UE26EH4510).The living room TV has a surround sound system so it will need to be compatible with DD, DTS etc: My media setup is shown below and all devices are connected via wired ethernet (Cat5). I am now considering at the Dell T30 which comes with 8GB of RAM and a 1TB HDD and I was going to purchase a 4TB WD Red to store my media on, so I can at least start using it as a media server. I was about to purchase the HP Microserver with an NVidia Shield as the Microserver processor is not as powerful for transcoding.īut then I realised that the cost of purchasing the 'HP Microserver AND an NVidia Shield' is the same cost as purchasing a higher spec server, because I wouldn't need to purchase an NVidia Shield as the server would be powerful enough to transcode. I have no experience of server hardware and software but someone suggested using FreeNAS as the OS, which is why I am here. iTunes library (to play via my Denon AVR).General backup of photos/documents/video etc.I am looking for a server initially to act as a media server for Plex/Emby/Kodi, can I do this using only one HDD for the media storage ?Īfter briefly playing with Plex/Emby/Kodi using my Mac Book Pro as a temporary server, I have found that I will need the server to transcode OR I will need a good media client such as the NVidia Shield to avoid the need to transcode.Įventually I would like to use the server for the following (when I can afford to purchase more HDDs):
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |